|
|
| |
|
|
 |
| PIR motion-87A Instruction |
|
|
 |
|
|
|
|
ALL Instructions |
| |
Adobe Reader |
| |
PRODUCT INTRODUCTION
The product is wireless passive infrared detector with high stability.
It has adopted advanced technology in signal processing and provided
superhigh detection ability and anti- error alarm. The detector will
detect human movement automatically when intruder pass through the
detected area, and it will send out alarm signal to alarm host that
there is movement. The product is suitable for the safety of
residential house, villas, factories, markets, warehouses, office
building etc.
MAIN FEATURE
ASIC Adopted
Auto temperature compensation
Send alarm signal by RF
Adjustable detecting distance
Low battery indication
SMT design adopted
TECHNICAL SPECIFICATION
Operation voltage: DC 3V (2*AA battery)
Static current: ≤25uA
Alarm current: ≤55mA
Detecting distance: 9～18m
Detecting angle: 2~4°
Code form: 2262 or 1527
Radio frequency: 315MHz or 433MHz
Radio distance: 200m(open area)
Low battery indicator: yellow LED
Alarm indicator: red LED
Range of coverage: 11 distance, 8 middle, 5 vicinities
Sensor: dual element infrared sensor
Operating temperature: -10℃～50℃
Environment humidity: ≤95%RH(no congelation)
Anti RF interference: 10MHz-1GHz 20V/m
Installation mode: wall mounted or hanged in corner
Installation height: 1.7 to 2.5m(2.2m is proposed)
Outline Size: 59L*39.5W*107H mm
INSTALLATION
1.Installation at the out door, place with pets, air-condition nearby,
direct sunshine, heat source and under the rotating objects should be
avoided.
2. Surface of installation should be firm with no vibration.
3.Installing the detector in the place where intruder pass easily.
4. Fixing bracket on the wall by screw.
5. Hang the detector, it will work normally after turning on the power
switch.
OPERATING INSTRUCTION - Function Setting
1.Delay Jumper: used to set alarm delay time. When set to Test Mode(5
seconds), it will be triggered every 5 seconds when it has been triggered,
while set to Work Mode(5minuters), it will be triggered every 5 minutes
when it has been triggered.
Short 1&2: delay 5s(test mode)
Short 2&3: delay 5 minutes(work mode)
2.Code Jumper: used to set address code and zone code with alarm host.
A0-A7 is address code, which should correspond with alarm host. (No need
for 1527 code IC) D0-D3 is data code for setting defence zone.
3.LED Jumper: for setting LED ON or OFF without effect of the detector work.
Short 1&2: set LED ON
Short 2&3: set LED OFF
LED can be shut for concealment of the detector after test.
4.RF Sw: Button for testing, when press the button, the detector sends alarm
signal to the alarm host. When use a learning alarm host, please set the
host at the state of learning.
5.RANGE Jumper: Use to set detecting distance in your need.
6.Yelllow LED: Low battery indicator, when the LED on, please charge the
batteries in time.
OPERATING INSTRUCTION - Product testing
Turning on power and LED indicator will flashed for 1s, the detector comes
into state of self check, it takes about 30s, after that it is in the state
of normal work. Conner should walk parallel with the wall installed detector
in the testing area. LED lighting means the detector is in the state of alarm.
NOTICE
1.Please install and use the detector according to this manual, don't touch
the surface of sensor for avoiding affecting the sensitivity of the detector.
Please shut off power and then clean the sensor by soft clothe with little
alcohol if cleaning needed.
2.The product can reduce accident but may not perform as expected. The user
is advised to take all necessary precautions for his/her safety and the
protection of his/her property.
3.In order to ensure it can work normally, the power should be kept to supply
and get on walking test periodically, once a week is better.
|
|
|
